2024 Leads4pass Free Latest IT Cert Exam Dumps

2017 latest Cisco CCNA 200-125 dumps exam practice materials and study guides free download from lead4pass. High quality Cisco CCNA 200-125 dumps pdf files and dumps vce youtube update free demo. https://www.leads4pass.com/200-125.html dumps exam training resources. Get the best Cisco CCNA 200-125 dumps exam questions and answers from lead4pass, pass Cisco 200-125 exam test easily at the first time.

Latest Cisco 200-125 dumps pdf practice materials: https://drive.google.com/open?id=0B_7qiYkH83VRSnZDMkVUWDJzLWM

Latest Cisco 300-101 dumps pdf practice materials: https://drive.google.com/open?id=0B_7qiYkH83VRWFlVNGtTZjU1MVE

Vendor: Cisco
Certifications: CCNA
Exam Name: CCNA Cisco Certified Network Associate CCNA (v3.0)
Exam Code: 200-125
Total Questions: 966 Q&As

QUESTION 1
If primary and secondary root switches with priority 16384 both experience catastrophic losses, which tertiary switch can take over?
A. a switch with priority 20480
B. a switch with priority 8192
C. a switch with priority 4096
D. a switch with priority 12288
Correct Answer: A

QUESTION 2
After you configure the Loopback0 interface, which command can you enter to verify the status of the interface and determine whether fast switching is enabled?
A. Router#show ip interface loopback 0
B. Router#show run
C. Router#show interface loopback 0
D. Router#show ip interface brief
Correct Answer: A

QUESTION 3
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security mac-address 1
Correct Answer: C

QUESTION 4
Which command can you enter to set the default route for all traffic to an interface? 200-125 dumps
A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
C. router(config-router)#default-information originate
D. router(config-router)#default-information originate always
Correct Answer: A

QUESTION 5
Which two statements about IPv6 and routing protocols are true? (Choose two.)
A. Link-local addresses are used to form routing adjacencies.
B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.
Correct Answer: AB

QUESTION 6
Which three commands can you use to set a router boot image? (Choose three.)
A. Router(config)# boot system flash c4500-p-mz.121-20.bin
B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin
E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin
F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin
Correct Answer: ABC

QUESTION 7
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.

The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem? 200-125 dumps
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
Correct Answer: D

QUESTION 8
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?
A. Switch(config)#vlan 20
Switch(config)#Interface gig x/y
Switch(config-if)#switchport access vlan 20
B. Switch(config)#Interface gig x/y
Switch(config-if)#vlan 20
Switch(config-vlan)#switchport access vlan 20
C. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk native vlan 20
D. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport access vlan 20
E. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk allowed vlan 20
Exam ACorrect Answer: A

QUESTION 9
Which two statements about late collisions are true? (Choose two.)
A. They may indicate a duplex mismatch.
B. By definition, they occur after the 512th bit of the frame has been transmitted.
C. They indicate received frames that did not pass the FCS match.
D. They are frames that exceed 1518 bytes.
E. They occur when CRC errors and interference occur on the cable.
Correct Answer: AB

QUESTION 10
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation frame-relay
Main(config-if)# authentication chap
Main(config-if)# no shut
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252
Main(config-if)#encapsulation ietf
Main(config-if)# no shut
Correct Answer: B

QUESTION 11
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. 200-125 dumps
The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?
A. the OSPF route
B. the EIGRP route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Correct Answer: B

QUESTION 12
What will happen if a private IP address is assigned to a public interface connected to an ISP?
A. Addresses in a private range will be not be routed on the Internet backbone.
B. Only the ISP router will have the capability to access the public network.
C. The NAT process will be used to translate this address to a valid IP address.
D. A conflict of IP addresses happens, because other public routers can use the same range.
Correct Answer: A

Read more: https://www.leads4pass.com/200-125.html dumps questions and answers free update.

Watch the video to learn more: https://youtu.be/nF4Ul2viODM